Ammochostos iaaonlin
08-09-21 1 Hits

The weather people are forecasting up to 20 named storms this season. While the high winds and hurricanes are bad enough, the storm surge with its deadly flooding is a big challenge too. There will not be enough boats to do the work that will be left behind in the storms’ wake, so firefighters cannot afford to have any downtime when it comes to this valuable resource. This article will cover many inspection and maintenance points to help ensure your water response to your community and keep you from needing to be rescued yourself.

    Inspection of Outboard Motor

    The fairing is the outer cover of the powerhead and is designed to allow air in to cool the engine and keep water out. Check the general condition of the gasket located at the bottom of the fairing. Check the general condition of the gasket located at the bottom of the fairing.

    Make sure the fairing is free of cracks and locks securely.

    Check the fuel system, including the fuel filter. Check for cracked or corroded fuel tanks, leaking fuel line fittings, cracked fuel primer bulbs, and maintain at least 10% top space in the fuel cell. Ethanol fuels should be avoided as they will soften rubber parts.

    Check for water in the fuel.

    Check that the throttle and shift controls move freely.

    Check the integrity of the cross member and mounting brackets. Check the propeller. Lubricate the drive shaft.

    Note that the engine can be 4-cycle or 2-cycle. Check the oil as needed.

    After use, flush the engine cooling system with water.

    If you've read our article on car engines, you'll know that they produce motion by burning gasoline with oxygen in metal cylinders. The cylinders have sliding pistons that push a crank around and the crank drives a shaft that (eventually) powers the wheels. Much the same happens in an air cooled outboard motor. The main difference is that there are usually fewer cylinders, operating in either a two-stage or four-stage cycle. Instead of driving a gearbox, the motor powers a propeller. To steer a boat with an outboard motor, you simply tilt the whole motor casing so the propeller pushes the water away from it at an angle. (Some outboards you can tilt by hand; others are steered by turning a steering wheel that tilts the water cooled outboard motor using hydraulic cables.) You can go faster by opening up the throttle so the outboard burns more fuel and turns over more quickly.

    Who invented outboards?

    Frenchman Gustave Trouvé designed the first electric-powered outboard motor around 1870 and made his first voyage in it on May 26, 1881. It wasn't the most practical invention at a time when batteries were huge and heavy. You can see how low the boat is sitting in the water, which might be a bit of artistic flair—or a reflection of how perilious this pioneering voyage really was! And what about "mixing" electricity and water with all those wires strung around you? Gasoline-powered outboards followed about 20 years later and were developed by such pioneers as Ole Evinrude of Milwaukee (who patented a method of water cooling outboards in 1928) and the Swedish brothers Carl and Oscar Hult, who studied and improved on Evinrude's designs.

    Apart from keeping your boat’s hull clean and your outboard or engine tuned, selecting the right propeller is one of the easiest actions you can take to optimize boat performance. Depending on how you use your boat and its current performance, you might be wondering if you should “pitch up”, “pitch down”, switch from aluminum boat to stainless steel, or move from three blades to four. Your prop might be damaged and need replacement.

>https://www.tomkingoutboard.com/

  Send Message

Related ads

What is a Junction Box?

  Junction boxes are metal or plastic enclosures used as housings for wiring connections. The connections within are called branch circuits and usually represent the end of a conduit run. Junction boxes make wire access easy, since all one must do is… Ammochostos

Love spell to get your ex back +27635090276 Durango Englewood Estes Park Fort Collins Fort Morgan Georgetown Glenwood Springs Golden

CALL ☎:/What-Sapp: +27635090276 Dr. PAPA WAVAR  of Spiritual Love Spells Powerful Psychic Love Spells that work, Best Traditional Spiritual Healer | Herbalist | Sangoma with trusted Spells | World’s Top lost love spells caster, couple break up spells,… Ammochostos

How Oxygen and Nitrogen generators are used in manufacturing companies

    The air we breathe contains two gases that are extremely useful in industry: oxygen (about 21%) and nitrogen (about 78%). Adding oxygen to a process enables better control of heating patterns, higher furnace efficiencies (for lower fuel consumption)… Ammochostos

An Introduction to Machine Vision Systems

Machine vision systems are a set of integrated components that are designed to use information extracted from digital images to automatically guide manufacturing and production operations such as go/no testing and quality control processes. These systems… Ammochostos

Desiccant or compressor dehumidifier?

DESICCANT DEHUMIDIFIERS     While a compressor dehumidifier has a compressor and a cold surface that it utilizes to yank the moisture from the damp air, the desiccant dehumidifier works more like a sponge or silica gel, simply absorbing the moisture from… Ammochostos

Report this ad

Currencies

Map

Language


© CYCLASSIFIEDS - 2020